How to Do a Door Lock Change
Changing your door lock is a simple and inexpensive way to increase the security of your home. This isn’t for all. It requires a certain amount of patience and expertise.
The cylinder is inside the knob’s body. The cylinder recognizes the key when it is inserted into the lock.
Removing the old lock
First, you must remove the lock that was previously in place. This is a relatively easy process, however there are a few points to keep in mind. Make sure the new lock fits the door. This will ensure that it is secure and doesn’t leave a gap at the deadbolt or latch.
After removing the latch plate, you’ll be required to search for two bolts or lock replacement Upvc door screws in the casing’s interior which are holding the casing together with the lock halves. Remove these screws with a screwdriver before removing the lock off the upvc door locks. If you are using a mortise locking system there is a set screw that binds the handle to the spindle. Make use of a screwdriver for removing this screw, then remove the doorknobs.
You should also remove the deadbolt latch and latch plug from the hole in your door jamb. Then, you can put in your new lock. If you are replacing a mortise lock you should also measure the distance between the lock case and the door’s edge to ensure that your new lock will fit.
It is possible to replace your lock for a variety of reasons, for instance, if you suspect that someone else holds the key, or if you’ve got new roommates. You can save money by deciding to remove the lock yourself instead of hiring an expert. The process is easier than many people imagine and can be done in a few minutes.
Remove the trim and handle from your door. Then, pry the trim off with a flat screwdriver. You should be able twist off the majority of it. In some instances you might be able to remove the handles completely. The next step is to look for a hole on the inside of the handle and then insert an unstraightened clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look for another small tab that is located inside of the lock and press it using a flat screwdriver. After the spindle is removed, you can take off the cylinder and housing.
Making a decision on a new locking system
You have many options when it comes to choosing a new lock. Think about the various kinds of locks and choose one that matches the design of your door. Think about the backset, which is the distance between the edge and the center of lock hole. Also, consider the cross bore, a small hole at the edge of your door’s frame. Select a lock that will fit the door thickness and the swing.
The majority of door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they stand up to use and how difficult they are to disable or pick. A grade 3 lock may be perfect for a quiet apartment building in the countryside, whereas locks that are grade 1 might be more appropriate for the busy streets near a storefront.
Most smart door locks require a digital code to open. If you are worried about hacking, or any other security issues, talk to a professional locksmith.
Replacing the cylinder
You can easily replace a damaged or broken door lock cylinder with a simple DIY project. It is essential to choose the correct cylinder and follow all instructions. First, remove the knob or handle, if it is present. Then, using a screwdriver, remove the trim that is around the lock cylinder. Once the trim has been removed, you can take off the screws that hold the cylinder in place using the flathead. The cylinder is then gently pulled from the door.
Make sure you take measurements of the length of the new cylinder prior to putting it in place. Take a measurement of the distance from the center to the right and left sides of the cylinder using an instrument. Then, buy an additional cylinder using the same measurements. This will stop cylinders from snapping when doors are kicked or the key gets stuck inside.
Once you have a suitable replacement lock for upvc door cylinder, put it into the door and turn the key. This will align the cylinder with your carrier which is typically on the outside of the lock. You can then loosen the set screws, which should be a couple of turns in the head. If there is a screw on the outside of the case that is holding the door, you will have to loosen it.
After you have removed the lock replacement Upvc door cylinder after which you can replace it with a new lock by sliding the new cylinder into the case and tightening the set screw. Installing the part that connects the cylinder to a lock indicator stem is also crucial. It is done by pulling three tabs in the back of the cylindrical with needle-nosed pliers. Then, you can attach the second bracket to the back of the cylinder. Then, you should reinstall the strike plate and latch plate, along with the retaining rings fixed to the top of the lock cylinder.
Installing a new lock
Start by measuring the door’s width if you are replacing a lock that is already in use. Most residential locksets have a thickness of 1 3/8 to 1 3/4 inches. If your door is more thick, you will need a door kit that is thick and includes longer screws as well as an extended tail piece (for door knobs) or spindle extensions (for deadbolts).
The majority of locks come with a comprehensive installation guide to assist you. Take the time to read the instructions before starting the process to make sure that you’ve followed all the steps. The guide will also provide you with an idea of the level of skill required to accomplish the task. You may want to ask a friend who has had experience in changing locks for assistance if you are changing window locks for upvc windows for the first time.
Before installing the new lock, it’s a good idea to cover the holes with tape the old hardware. This will prevent the screws from falling through the holes and will also protect any tiles you may have put in. This will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch comes with a strip of masking or gaffer tape, but you can use any tape you have.
After removing the screws that hold the lock’s inner half to the exterior then pull the lock straight away. It’s crucial to do this swiftly to prevent the lock from closing itself in a way that could end up damage the mechanism.
If the new lock comes with a latch bolt, fit the new latch bolt into its upper cross bore. Make sure that you put it in the correct place as marked by an arrow on the faceplate. Then, screw the latch plate onto the bolt.
Screw the deadbolt to the jamb of the door. Test the deadbolt by throwing it few times to verify that it extends all the way through the strike plate and is completely secured. If you’re using an electronic smart lock, make sure to follow the instructions for programming it. This involves downloading an application and registering your e-mail address, verifying your identity and connecting to the wireless network in order to connect your device.